Pair of quality YSS rear shock absorbers, milled aluminium body with black springs. These fit series 2 Nevada 750 models

Continuous preload adjustment, fully rebuildable

 This part is available by special order, request a quote

Pair of quality YSS rear shock absorbers, milled aluminium body with black springs. These fit series 1 Nevada 750 models (those originally fitted with Bitubo shocks)

Continuous preload adjustment, fully rebuildable

 This part is available by special order, request a quote

Pair of YSS rear shock absorbers, milled aluminium body with black springs.

Continuous preload adjustment, fully rebuildable

 This part is available by special order, request a quote

Pair of Nitro Race Piggyback Stainless Steel Shocks. Featuring a stainless steel 38mm damper unit with 90mm piggyback reservoir, fully re-buildable, 18mm piston rod, 10 position damping adjustment with automatic compression / rebound balance. 73mm outside diameter natural stainless steel spring, silver anodised aluminium fittings. Fully progressive spring pre-load adjustment. Supplied as a complete pair with mounting bushes, spring adjusting C spanner and 2.5mm hexagon key. These units are designed to be fitted with the damping adjuster at the bottom but will operate in either orientation.

The suspension on the V7 II models is notoriously cheap and is upgraded by most owners, but all V7 models will benefit from this suspension upgrade which will transform handling. Fully adjustable damping and preload allows you to set up your bike handling as it should.

Combine with our fork upgrade kit to transform the handling of your V7.

All Hagon shocks have a 2 year unlimited kilometer guarantee and are TUV approved. Also available by special order with chromed springs and/or polished alloy body, please enquire for details. All Hagon shocks have a 2 year unlimited kilometer guarantee and are TUV approved.

 This part is available by special order, request a quote

Rebuild kit for Brembo P32 rear caliper. This is a comprehensive overhaul kit containing replacement dust seals, fluid seals, o ring, bleed nipple, dust cap, washers, brake grease and caliper bolts. One kit required per caliper. Also suitable for some Ducati / Aprilia models.

Caliper seal kit

 This part is available by special order, request a quote

Rebuild kit for Brembo rear caliper. This is a comprehensive overhaul kit containing dust seals, fluid seals, o ring, bleed nipple, and dust cap

Caliper seal kit

 This part is available by special order, request a quote

This adjustable fuelling modifier uses the lambda sensor signal to the ECU. By modifying that signal it achieves an improvement in low and midrange throttle response. Comes with wiring harness and instruction manual, installation is simple and does not require any specialist tools. Suitable for all single throttle body V7, V9 and V85 TT models.

Rapid Bike EASY: A base level simple plug and play modulator equipped with a microprocessor managing the lambda sensor signal to optimize the air/fuel ratio, improve the engine efficiency and eliminate power gaps typical of the low and medium rpm range.

See installation instructions here.

 Order now and we will post your order within 7 days.

Rubber oil seal for top of pushrod

 2 in stock

 27045420 GU27045420 27 04 54 20
 2704 5420 2704.5420 27.04.54.20

Brembo PS 16 rear master cylinder for models with a remote reservoir, suitable as a replacement for the standard PS15 master cylinder which has now been discontinued by Brembo. Supplied with operating lever. Mounting holes at 50mm centres

Brembo ref. 10.2934.02 See BRA19500 for the elbow that the fluid supply pipe fits onto. Also see BRC19001 for a reconditioned PS15 MC

 This part is due back in stock soon, call 01484 841395 to reserve yours

 19667000 GU19667000 19 66 70 00
 1966 7000 1966.7000 19.66.70.00

Profesionally rebuilt Brembo PS 15 rear master cylinder for models with a remote reservoir. Mounting holes at 50mm centres.

Brembo ref. 10.2934.02
Usually supplied as a bare master cylinder with a piston installed. Spring, operating lever and input elbow may not be included. See BRA19500 for the elbow that the fluid supply pipe fits on to and BRA19667 for the return spring. Send us your old rebuildable (i.e. with a undamaged bore) PS15 for a £10 credit against your next order.

 19667000 GU19667000 19 66 70 00
 1966 7000 1966.7000 19.66.70.00